Eurotherm Continental Industries SV Solid State Relay, SSR, Hockey Puck Relay

SV Family -- With Superior Surge Survival™
Features: Optically isolated LED status indicator Clear safety cover included 800 volt blocking voltage (3V models) 1200 volt blocking voltage (6V models) 4000 volt isolation Zero voltage turn-on Improved built-in snubber High surge capability 100% tested at rated current U.L. recognized C.S.A. certified CE compliance		Click Here For: Data Bulletin .pdf Dimensioned Drawing Derating information, heat calculations Schematics Heatsinks Thermal Pads (thermal transfer grease) Glossary of Terms Information Request

Input: 4 to 32 VDC	Model ->	SVDA/ 3V10	SVDA/ 3V25	SVDA/- 3V50	SVDA/- 3V75	SVDA/- 6V50	SVDA/- 6V75
Schematic Number		1	1	1	1	1	1
Impedance (Rc)	Ohm	1500	1500	1500	1500	1500	1500
Turn-on Voltage (Min.)	VDC	4V@5.4mA	4V@5.4mA	4V@3.5mA	4V@3.5mA	4V@3.5mA	4V@3.5mA
Turn-on Voltage (Max.)	VDC	32V@10mA Max (current limited)	32V@10mA Max (current limited)	32V@6.5mA Max (current limited)	32V@6.5mA Max (current limited)	32V@6.5mA Max (current limited)	32V@6.5mA Max (current limited)
Turn-off Voltage (Max.)	VDC	1	1	1	1	1	1
Reverse Voltage Protection	VDC	-75	-75	-75	-75	-75	-75

Input: 100 to 280 VAC	Model ->	SVAA/ 3V10	SVAA/ 3V25	SVAA/ 3V50	SVAA/ 3V75	SVAA/ 6V50	SVAA/ 6V75
Schematic Number	0	2	2	2	2	2	2
Impedance (Rc)	KOhm	20	20	20	20	20	20
Turn-on Voltage (Min.)	VAC	100	100	100	100	100	100
Turn-off Voltage (Max.)	VAC	20	20	20	20	20	20
Reverse Voltage Protection		N/A	N/A	N/A	N/A	N/A	N/A

Output: (For All Models)
I_OUT(Continuous w/proper heatsink)	A_RMS	10	25	50	75	50	75
Voltage Drop @ I_OUT	VAC	1.1	1.2	1.3	1.1	1.3	1.1
I_SURGE- 1 Cycle Non-repetitive	A_PEAK	100	250	650	950	650	950
I_SURGE- 1 Second Non-repetitive	A_PEAK	40	100	130	140	130	140
Voltage Range (V_OUT)	VAC	24-330	24-330	24-330	24-330	24-660	24-660
Peak Blocking Voltage		800	800	800	800	1200	1200
Frequency Range	Hz	47-63	47-63	47-63	47-63	47-63	47-63
Leakage @ V_OUT(max.)	mA	8	8	8	8	8	8
Turn-on (max.)		1/2 cycle	1/2 cycle	1/2 cycle	1/2 cycle	1/2 cycle	1/2 cycle
Turn-off (max.)		1/2 cycle	1/2 cycle	1/2 cycle	1/2 cycle	1/2 cycle	1/2 cycle
Holding current (min.)	mA	50	50	50	50	50	50
Zero voltage switching		Yes	Yes	Yes	Yes	Yes	Yes
Dv/Dt @ V_OUT(max.)	Vus	750	750	1000	1000	500	500
Commutating Dv/Dt Snubbed for Power Factor.=		.5	.5	.5	.5	.5	.5
I²T Fusing (8.3 ms.)	A²S	35	260	1035	3745	1035	3745
Thermal resistance R_0JC(Tj=115^oC)	⁰C/W	1.48	1.05	.65	.30	.65	.65

General Characteristics:
Dielectric strength (Input-Output-Base)	V_RMS	4000	4000	4000	4000	4000	4000
Capacitance Input to Output	pf	3	3	3	3	3	3
Ambient temp. range (Operating)	⁰C	-40 to +100	-40 to +100	-40 to +100	-40 to +100	-40 to +100	-40 to +100

Adequate heatsinking, including consideration of air temperature and flow, is essential to the proper operation of a solid state relay. Units should not be mounted in an enclosed area without proper air flow. Units should also never be mounted to a plastic base or to a painted surface. Proper thermal transfer gel or pad should be applied to the heatsink before mounting the relay. Failure to provide adequate heatsinking will cause a solid state relay to fail.

Last updated May 25, 2004

SV Family -- With Superior Surge Survival™